Disclosure: when you buy through links on our site, we may earn an affiliate commission.

Basic electronics for Arduino Makers

An introduction to electronics to help you make the most from your Arduino or other prototyping platform.
4.7
4.7/5
(1,682 reviews)
11,953 students
Created by

9.4

CourseMarks Score®

9.1

Freshness

9.2

Feedback

9.2

Content

Platform: Udemy
Video: 7h 35m
Language: English
Next start: On Demand

Top Arduino courses:

Detailed Analysis

CourseMarks Score®

9.4 / 10

CourseMarks Score® helps students to find the best classes. We aggregate 18 factors, including freshness, student feedback and content diversity.

Freshness Score

9.1 / 10
This course was last updated on 9/2020.

Course content can become outdated quite quickly. After analysing 71,530 courses, we found that the highest rated courses are updated every year. If a course has not been updated for more than 2 years, you should carefully evaluate the course before enrolling.

Student Feedback

9.2 / 10
We analyzed factors such as the rating (4.7/5) and the ratio between the number of reviews and the number of students, which is a great signal of student commitment.

New courses are hard to evaluate because there are no or just a few student ratings, but Student Feedback Score helps you find great courses even with fewer reviews.

Content Score

9.2 / 10
Video Score: 8.7 / 10
The course includes 7h 35m video content. Courses with more videos usually have a higher average rating. We have found that the sweet spot is 16 hours of video, which is long enough to teach a topic comprehensively, but not overwhelming. Courses over 16 hours of video gets the maximum score.
The average video length is 4 hours 14 minutes of 178 Arduino courses on Udemy.
Detail Score: 9.4 / 10

The top online course contains a detailed description of the course, what you will learn and also a detailed description about the instructor.

Extra Content Score: 9.5 / 10

Tests, exercises, articles and other resources help students to better understand and deepen their understanding of the topic.

This course contains:

3 articles.
0 resource.
0 exercise.
0 tests or quizzes.

Table of contents

Description

Are you an Arduino maker, able to make things by following how-to guides and are confident with writing or modifying sketches, yet you are not so confident about things like calculating transistor currents, voltage drops and using capacitors as filters?
You are not alone. I have been teaching Arduino and Raspberry Pi topics for years. During this time I have realized that while these platforms are great for helping you to start tinkering with electronics, you will not be able to truly enjoy their power until you have understood basic electronics.
This is what this course is about. It is about helping you achieve a better level of understanding of the basic electronics principles and components that are commonly used in making on platforms like the Arduino and the Raspberry Pi.
I have designed this course for anyone with a basic understanding of electronics, who has already spent time tinkering with Arduinos. 
By the end of this course, you will have learned how to use commonly used components found in Arduino projects. You will also have learned how to do the relevant measurements and calculations to help you select appropriate components for your projects. 
To complete this course, you will need a few cheap and common components and tools: resistors, capacitors, transistors, LED, diodes, and batteries. You will also need a multimeter, a small breadboard and jumper wires. All of these are probably things that you already have.

You will learn

✓ Understand the concepts of voltage, resistance and current
✓ Use Ohm’s Law to calculate voltage, current and resistance
✓ Use Kirchhoff’s Laws to calculate voltage and current
✓ Understand the meaning of and calculate energy and power
✓ Use resistors in various configurations, like in voltage dividers and voltage ladders
✓ Read the value of a resistor from its package
✓ Use pull-up and pull-down resistors
✓ Understand the use of capacitors
✓ Use capacitors as energy stores and filters
✓ Calculate the RC time constant of a capacitor
✓ Understand diodes
✓ Measure the voltage drop of a diode
✓ Understand how to use rectifier and zener diodes
✓ Protect a circuit from reverse polarity
✓ Understand how to use a transistor to control low and high power loads
✓ Calculate the currents and base resistor for a bipolar transistor
✓ Use the correct voltage regulator for any circuit

Requirements

• Small circuits controlled by an Arduino
• A basic understanding of electricity and electronics
• Have assorted resistors, capacitors, LEDs, diodes, transistors, voltage regulators (see section 1 for details, free to view)A breadboard, jumper wires and a battery (see section 1 for details, free to view)A multimeter (see section 1 for details, free to view)Basic algebra

This course is for

• Anyone with minimal experience using an Arduino
• Anyone with minimal experience using any prototyping platform
• Anyone with a need to brush up their knowledge of basic electronics

How much does the Basic electronics for Arduino Makers course cost? Is it worth it?

The course costs $17.99. And currently there is a 82% discount on the original price of the course, which was $99.99. So you save $82 if you enroll the course now.
The average price is $13.0 of 178 Arduino courses on Udemy.

Does the Basic electronics for Arduino Makers course have a money back guarantee or refund policy?

YES, Basic electronics for Arduino Makers has a 30-day money back guarantee. The 30-day refund policy is designed to allow students to study without risk.

Are there any SCHOLARSHIPS for this course?

Currently we could not find a scholarship for the Basic electronics for Arduino Makers course, but there is a $82 discount from the original price ($99.99). So the current price is just $17.99.

Who is the instructor? Is Dr. Peter Dalmaris a SCAM or a TRUSTED instructor?

Dr. Peter Dalmaris has created 26 courses that got 15,813 reviews which are generally positive. Dr. Peter Dalmaris has taught 103,895 students and received a 4.6 average review out of 15,813 reviews. Depending on the information available, Dr. Peter Dalmaris is a TRUSTED instructor.
Educator and Author of “Maker Education Revolution”.


Peter Dalmaris is an educator, electrical engineer, electronics hobbyist, and Maker. Creator of online video courses on DIY electronics and author of three technical books, and has recently released his book Maker Education Revolution.  

As a Chief Tech Explorer since 2013 at Tech Explorations, the company he founded in Sydney, Australia, Peter’s mission is to explore technology and help educate the world. 

Tech Explorations offers educational courses and Bootcamps for electronics hobbyists, STEM students and STEM teachers.

A life-long learner, Peter’s core skill is in explaining difficult concepts through video and text. With over 15 years of tertiary teaching experience, Peter has developed a simple yet comprehensive style in teaching that students from all around the world appreciate. 

His passion for technology and in particular for the world of DIY open source hardware has been a dominant driver that has guided his personal development and his work through Tech Explorations.

Peter’s current online courses have helped over 60,000 people from around the world to be better Makers. 

For more information on Peter’s work, please go to his web site.

9.4

CourseMarks Score®

9.1

Freshness

9.2

Feedback

9.2

Content

Platform: Udemy
Video: 7h 35m
Language: English
Next start: On Demand

Students are also interested in